|
Four wheel drive, four wheel independent suspension
Front and Rear Ball Differental
Front Caster, Front and Rear Camber, Front toe-in adjustable
Chassis balance adjustable
Floating steering bar
Low center of gravity designed
4pcs.-6pcs. AAA battery (4.8V-7.2V)
Independent mini servo, ESC, receiver
Well fitted with most 1/24 scale model car body
Good performance on different surfaces
| Description |
Basic Kit |
Car Kit |
Ready Kit |
RTR Kit |
| Bodies |
Clear Body |
Clear Body |
Painted Body |
Painted Body |
| Assembly |
Factory fully pre-built; no Assembly work! |
| Micro Servo |
N/A |
Included |
| ESC |
N/A |
Included |
| Receiver |
N/A |
Included |
| Crystal Set |
N/A |
Included |
| Rechargeable Battery |
N/A |
4xAAA included |
| Transmitter |
N/A |
N/A |
N/A |
Included |
BASIC KIT:
- Car with clear body,
- fully built,
- no RS set,
- no Battery
CAR KIT:
- Car with clear body,
- fully built,
- with mini servo,
- ESC,
- receiver,
- crystal set,
- 4pcs. rechargeable battery
READY KIT:
- Car with painted body,
- fully built,
- with mini servo,
- ESC,
- receiver,
- crystal set,
- 4pcs. rechargeable battery
RTR KIT WITH TRANSMITTER:
- Car with painted body,
- fully built,
- with mini servo,
- ESC,
- receiver,
- crystal set,
- 4pcs. rechargeable battery,
- Futaba Megatech Sport Transmitter
SETTING:
UNDERSTEERING
1. More Camber - adjust the front lower arm knuckle ball
2. More Caster - upside down the front lower arm
3. Change front and rear tyre to type B (MP-26), or C (MP-27), or D (MP-28)
OVERSTEERING
1. Use short rear arm upper bar (included in the kit)
2. Adjust front ball differential screw more tight and rear ball differential screw slightly loose
3. Change rear tyre to type C (MP-27) or D (MP-28)
UNEQUAL STEERING
Adjust rear arm adjuster screw to keep the center of gravity
MORE SPEED
1. Full set of ball bearing (MO-01, 02)
2. Use 7.2V Battery (MO-08)
(Remember take off 6 battery connecting springs and remain input (+) and output (-) springs only)
Check the front lower arm suspension springs (MP18) from time to time and renew when it becomes soft in order to keep the car go straight especially when using 7.2V Battery.
Original Parts List:
MP-01 Chassis, Batt-spring 5pcs., Batt-cover 2pcs.
motor cover 2 pcs., screws 6 pcs
MP-02 Batt. Spring 5pcs.
MP-03 Ready Use Diff.Set 34T
MP-04 Ready Use Diff.Set 35T
MP-05 Ready Use Diff.Set 36T
MP-06 4WD motor 70T 0.22 wire
MP-07 Motor gear 8T 8pcs.
MP-08 Plastic bearing 8x12 4pcs., 3x6x2.5 6pcs.3x6x2 2pcs.
MP-09 F.knuckle & R.Hub set
MP-10 Wheel Set type A 4 pcs.
MP-11 Wheel Set type B 4 pcs.
MP-12 F.wheel shaft 2pcs., pin 2 pcs., nut 2pcs.
MP-13 R.wheel shaft 2pcs., pin 2 pcs., nut 2pcs.
MP-14 1.2x6 pin 4pcs., 1.6x16 pin 2pcs
MP-15 M3 lock nut 5pcs., 2x6 tapping screw 20pcs.,2x6 screw 10pcs.
MP-16 Arm set 10pcs.
MP-17 Arm shaft 4pcs.
MP-18 Suspension spring 8pcs.
MP-19 F.Drive shaft 2pcs.
MP-20 R.Drive shaft 2pcs.
MP-21 F.&R.Drive cover 4pcs., steering bar, motor cover 2pcs.
MP-22 3.8 steering ball 4pcs.
MP-23 Body Post 4pcs., Antenna tube
MP-24 Body clip 5pcs.
MP-25 Tyre set type A 4pcs.
MP-26 Tyre set type B 4pcs.
MP-27 Tyre set type C 4pcs.
MP-28 Tyre set type D 4pcs.
MP-29 Body w'window mask and painting mask, 'S'
MP-30 Body w'window mask and painting mask, 'C'
MP-31 Wing set for 'S'
MP-32 1.2V-700MA Ni-Mh AAA Batt. 4pcs.
MP-33 Servo cover & Motor Shaft mount 2pcs.
Option Parts:
MO-01 8x12 bearing 2pcs.
MO-02 3x6 bearing 2pcs.
MO-03 2x5 bearing 1pc.
MO-04 2WD motor
MO-05 Motor capacitor 4pcs.
MO-06 Painted body, 'S'
MO-07 Painted body, 'C'
MO-08 7.2V-700MA Batt.Pack
MO-09 27AM crystal set 26815-27690 (36 different freq.)
MO-10 Alu.wheel nut 4pcs.
MO-11 Color Antenna tube 8pcs.
MO-12 29AM crystal set 29725-29985 (20 different freqrency)
Electronic Parts:
Servo
ESC
Receiver without crystal
Radio Transmitter
 
 
 
 
Calibrationg procedures for the Mini-X ESC :
1. Turn the throttle trim to the neutral/middle of its adjustable range.
2. Switch Tx and Rx on
3. Leave the Tx alone and press and hold the setup switch of the ESC for 2 to 3 secs until both red and green LED turn On.
4. Release the setup button
5. Set the Tx to moving forwards direction and hold the throttle until the RED
6. Set the Tx to moving backwards direction and hold the throttle until the GREEN LED Turn On
Reviews from other websites:
Mini-z-bar.com - Mini-X review
RC baby.com - Mini-X Review I
RC baby.com - Mini-X Review II
Micro Racing - Mini-X Review
|
