Replacement & Upgrade Parts for Xpress RC Cars, Execute, GripXero, Xpresso & Stix Series
-120x120.jpg)
-120x120.jpg)
Model: XP-10316
Description:
Execute XM1 XM1S FM1S genuine official replacement part from Xpress...
Model: XP-10178
Description:
This is Xpress genuine official replacement part for Execute Touring Series. Included are a set of front and rear rollbars...
Model: XP-10883
Description:Replacement parts for the Xpress Arrow AT1, genuine part for Xpress series of cars...
Model: XP-10327
Description:
Bushing set for installing optional rollbars onto your Execute XQ1S! Comes with all mounting hardware for installing this part...
Model: XP-11203
Description:Anti-roll bar set for the Xpress Execute XQ3S, providing you with better cornering stability. Included are three different thicknesses for you to fine tune your setup for the track you're running on!..
Model: XP-11034
Aluminum bottom chassis for Xpress Arrow AT1, used for in either High Grip Asphalt or Carpet. By adding more weight to the lowest point of the chassis, this increases stability and lowers the center of gravity!..
Model: XP-11042
Aluminum bottom chassis for Xpress Arrow AT1, used for in either High Grip Asphalt or Carpet. By adding more weight to the lowest point of the chassis, this increases stability and lowers the center of gravity! A lighter version of the AT1 aluminum chassis plate for use in medium grip tracks where t..
New
Model: XP-11310
Aluminum skidblock for your Xpress rally chassis, further protecting your chassis whilst being lightweight!..
New
Model: XP-11294
Aluminum upgrade steering bridge for the Arrow AT1SR rally car for a more direct steering response.
Note: Bearing hole is made smaller than usual to reduce steering rack slop and bearing may be harder to install than usual...
New
Model: XP-11224
Special red edition graphite decks for your Xpress shaft drive Rally Car!..
New
Model: XP-11225
Special red edition graphite decks for your Xpress shaft drive Rally Car!..
New
Model: XP-11226
Special red edition graphite decks for your Xpress shaft drive Rally Car!..
New
Model: XP-11200
Replacement shock shafts for your Arrow rally car! Replace as they get scratched from the dust and stones on your offroad races or bashes!..
New
Model: XP-40257
Description:Replacement bearing for the belt tensioner portion of the motor mount on the Execute XQ11..
Model: XP-40249
Replacement bearing for the center pulley in the Execute XQ3S / XQ11 / XQ11R...
Model: XP-40195
Bearings for the propeller shaft assembly of the Arrow AT1 / AM1 / AT1S / AM1S, replace bearings to keep your drivetrain smooth and efficent...
Model: XP-40250
Replacement bearing for the wheel hub in the Execute XQ3S / XQ11 / XQ11R...
Model: XP-40196
Bearings for the diff of the Arrow AT1, replace bearings to keep your drivetrain smooth and efficent...
Model: XP-10155
Description:
Full set of Anti-roll bars for the Execute XQ1, XQ10, XQ10F, FT1, ranges from 1.2 to 1.4 which should cover all required roll-bar dimensions for different tracks...
Model: XP-10054
Xpress Ball Bearing Set For Xpresso K1 M1 #XP-10054
Description:
This is Xpress Replacement Ball Bearing Set, genuine official replacement part from Xpress...
Model: XP-10630
Bando branded belts for the Mid Motor 1/10 Touring Series of Execute Cars, made for longer lifespan but sacrificing some durability at the same time for use when using high powered motors!..
Model: XP-10575
Belts made from a kevlar material for the Execute FT1 series, made for longer lifespan but sacrificing some durability at the same time for use when using high powered motors!..
Model: XP-10350
Description:
Bando branded belts for the Execute XM1 / XM1S, made for longer lifespan but sacrificing some durability at the same time for use when using high powered motors!..
Model: XP-10351
Description:
Bando branded belts for the Execute XM1 series, made for longer lifespan but sacrificing some durability at the same time for use when using high powered motors!..
Model: XP-10731
Description:Upgrade Bando belts for the Xpress Execute FM1S and XQ10F, for higher efficiency in your drivetrain!..
Model: XP-11206
Description:Barrel shaped springs for 1/10 touring car, giving a progressive spring action without changing the spacing of the spring. Resulting in a more predictable handling car improving lap consistency. Your choice of 19 or 20mm widest width, with 19mm being stiffer than 20mm of the same coil nu..
Model: XP-11210
Description:Barrel shaped springs for 1/10 touring car, giving a progressive spring action without changing the spacing of the spring. Resulting in a more predictable handling car improving lap consistency. Your choice of 19 or 20mm widest width, with 19mm being stiffer than 20mm of the same coil nu..
Model: XP-11207
Description:Barrel shaped springs for 1/10 touring car, giving a progressive spring action without changing the spacing of the spring. Resulting in a more predictable handling car improving lap consistency. Your choice of 19 or 20mm widest width, with 19mm being stiffer than 20mm of the same coil nu..
Model: XP-11211
Description:Barrel shaped springs for 1/10 touring car, giving a progressive spring action without changing the spacing of the spring. Resulting in a more predictable handling car improving lap consistency. Your choice of 19 or 20mm widest width, with 19mm being stiffer than 20mm of the same coil nu..
Model: XP-11208
Description:Barrel shaped springs for 1/10 touring car, giving a progressive spring action without changing the spacing of the spring. Resulting in a more predictable handling car improving lap consistency. Your choice of 19 or 20mm widest width, with 19mm being stiffer than 20mm of the same coil nu..
Model: XP-11212
Description:Barrel shaped springs for 1/10 touring car, giving a progressive spring action without changing the spacing of the spring. Resulting in a more predictable handling car improving lap consistency. Your choice of 19 or 20mm widest width, with 19mm being stiffer than 20mm of the same coil nu..
Model: XP-11209
Description:Barrel shaped springs for 1/10 touring car, giving a progressive spring action without changing the spacing of the spring. Resulting in a more predictable handling car improving lap consistency. Your choice of 19 or 20mm widest width, with 19mm being stiffer than 20mm of the same coil nu..
Model: XP-11213
Description:Barrel shaped springs for 1/10 touring car, giving a progressive spring action without changing the spacing of the spring. Resulting in a more predictable handling car improving lap consistency. Your choice of 19 or 20mm widest width, with 19mm being stiffer than 20mm of the same coil nu..
Model: XP-10005
Description:
This is Xpress Battery Mount Set, genuine official replacement part from Xpress...
Model: XP-40062
Replacement bearings for the Center pulley found on the Execute XQ1...
Model: XP-10882
Description:Replacement parts for the Xpress Arrow AT1, genuine part for Xpress series of cars. ..
Model: XP-10992
Replacement parts for the Xpress Arrow AT1S / AM1S, genuine part for Xpress series of cars...
Model: XP-10939
Replacement parts for the Xpress Arrow AT1, genuine part for Xpress series of cars. Self lubricating composite to keep your drivetrain smooth...
Model: XP-10396
Description:
Replacement shock parts for the Sports Short Shocks XP-10797 as well as on the Execute XQ2S DR1S ! Keep some spares or change out when your original parts develop slop from collisions on the track! Enough parts in one pack to rebuild four shocks!..
Model: XP-10055
This is Xpress Body Clips 20pcs,genuine official replacement part from Xpress...
Model: XP-10819
Body support braces to be used in conjunction with the new V2 Strong C Hubs, found on the Execute XQ2S, DR1S or even for upgrading your Execute series car!**Note: For Execute XQ1, XQ10, XQ10F, XM1, FT1, XQ1S, XM1S, FT1S, FM1S, need to use with V2 Strong Composite C Hub 4 Degree #XP-10400 or Hard Str..
Model: XP-10198
Description:
Using these brass suspension pieces allows you to increase the weight without affecting the left to right balance! Direct replacement for the original two piece suspension mount.
Note: When install on XQ1S, XQ2S, FT1S, XM1S, FM1S, DR1S and other sport series Execute Chassis replacing th..
Model: XP-10557
Description:
Control flex under the diff/spool area with this easy to install piece of graphite and brass. The brass piece also allows you to tune the weight bias of the car!..
Model: XP-10242
Description:
Brass made balancing weights which screw onto the chassis of the Execute Touring and secured in place with another locking pin...
Model: XP-10186
Description:
Brass made balancing weights which screw onto the chassis plate of the Execute series and secured in place with another locking pin...
Model: XP-10199
Description:
Using this brass suspension piece allows you to increase the weight without affecting the left to right balance!
Note: When install on XQ1S, XQ2S, FT1S, XM1S, FM1S, DR1S and other sport series Execute Chassis replacing the original composite suspension mount, need to use with #XP-10127 ..
Model: XP-10197
Description:
Adjust your chassis stiffness by changing to this optional one piece suspension mount for the rear of the front-end of your car! This suspension mount keeps the same width as the separate suspension pieces so the arm sweep angle isn't affected! Using this brass suspension piece allows y..
Model: XP-10638
Description:
Brass one piece FR suspension mount for all of the Execute Series of cars, enlarged slot allowing this to be used with the XQ1 Mid conversion kit as well! Use for more stability on high traction tracks!
Note: When install on XQ1S, XQ2S, FT1S, XM1S, FM1S, DR1S and other sport series Exe..
Model: XP-10723
Description:
Put some weight in the front part of mid motor FWD chassis in order to reduce weight shift to the rear end during acceleration, to increase the power effectiveness and cornering speed. The 31g weight is lighter then the one comes with the kit, educe the weight on the front tires with th..
Model: XP-10432
Description:
Genuine official option parts from Xpress Execute FT1 FT1S.Add more weight to the front of the chassis, to reduce weight shift to the rear part of the car, to increase the power efficiency and improve handling in mid of corner...
Model: XP-10927
Description:
Replacement 90g front lower brass piece for use with cars that feature the integrated bumper weight...
Model: XP-10196
Description:
Adjust your chassis stiffness by changing to this optional one piece suspension mount for the front of the rear end of your car! This suspension mount keeps the same width as the separate suspension pieces so the arm sweep angle isn't affected! Using this brass suspension piece allows y..
Model: XP-10200
Description:
Using this brass suspension piece allows you to increase the weight without affecting the left to right balance!Note: When install on XQ1S, XQ2S, FT1S, XM1S, FM1S, DR1S and other sport series Execute Chassis replacing the original composite suspension mount, need to use with #XP-10127 E..
Model: XP-11085
Description:Genuine Xpress replacement part, keep important spares in your pits box so your raceday or practice day isn't cut short!..
Model: XP-10925
Description:
Optional 90g front upper brass piece for use with cars that feature the integrated bumper weight...
Model: XP-40035
Description:
Genuine replacement part for Xpress series of cars...
Model: XP-40039
Genuine replacement part for Xpress series of cars...
Model: XP-40040
Genuine replacement part for Xpress series of cars...