Model: XP-10602
New 3.0mm outer suspension pins, to be used with the new "Strong" series of redesigned suspension arms for the Execute series!
**Note: If use this part on XQ1 or XQ1S, need to use with Composite Suspension Parts Set Hard Strong #XP-10565 or Strong Composite Suspension Parts Set #XP-10606..
Model: XP-10139
Description:This is 3.0mm Suspension Pivot Pin for Execute series, genuine official replacement part from Xpress...
Model: XP-40002
Description:
Cool your ESC in hot temperatures with this aluminum cased fan. With the aluminum case, allowing for it to act as a heatsink to help dissipate heat..
Model: XP-10334
Spring steel double jointed universals with a replaceable pin to exchange when worn out! Smoother cornering when compared to traditional single jointed universals!
Note: When using this part for upgrading the universal shaft from XQ1S, XQ2S, FT1S and DR1S, need to change the 5x10x4mm ball bearing at..
Model: XP-11044
Steel Double Joint Universal Shaft Pair for Execute Series Touring Chassis, genuine official replacement part from Xpress. With double joint universal shaft will greatly minimize the vibration of the outside front wheel in corners and improves the cornering speed and stability. These measure in at 3..
Model: XP-11280
3D printed TPU bumper, offering enough support to keep body from deforming during cornering whilst also absorbing hits! Curved base reduced the chance of the bumper from scraping on the floor and giving you better cornering efficiency...
Model: XP-10716
Description:Original replacement part for the Execute XQ10F and XQ10 FWD conversion Kit, keep spares ready so your race day won't cut short!..
Model: XP-10289
Description:
Execute XM1 XM1S FM1S genuine official replacement part from Xpress...
Model: XP-10377
Description:
Flat pin suspension pivot pin, for use in both the front C hub and rear hub. The flat spot allows for more surface area for the set screw to secure the pin in place and prevent it from flying out...
Model: XP-10874
Description:Replacement parts for the Xpress Arrow AT1, genuine part for Xpress series of cars...
Model: XP-10378
Description:
Replacement damper piston for Xpress's K1 M1 XQ1S XM1S D1 FM1S, featuring four holes for a lighter dampening effect in your shocks!..
Model: XP-10151
Description:This is Xpress 4.8mm Ball 10mm Thread, 10pcs package, genuine official replacement part...
Model: XP-10239
Description:This is Xpress 4.8mm Ball 10mm Thread 4pcs, genuine official replacement parts for Xpress...
Model: XP-10148
Description:
This is Xpress 4.8mm Ball 5mm Thread, 10pcs package, genuine official replacement part from Xpress...
Model: XP-10236
This is Xpress 4.8mm Ball 5mm Thread, 4pcs package, genuine official replacement part...
Model: XP-10149
Description:
This is Xpress 4.8mm Ball 6mm Thread, 10 pcs package, genuine official replacement part from Xpress...
Model: XP-10237
This is Xpress 4.8mm Ball 6mm Thread, 4pcs package, genuine official replacement part...
Model: XP-10150
Description:
This is Xpress 4.8mm Ball 8mm Thread, 10pcs package, genuine official replacement part from Xpress...
Model: XP-10044
Description:
This is Xpress 4.8mm Ball Set, genuine official replacement part from Xpress...
Model: XP-10238
This is Xpress genuine official replacement part for Execute...
Model: XP-10003
Description:
This is Xpress 4.8mm Ball End & Suspension Parts, genuine official replacement part from Xpress...
Model: XP-10002
This is Xpress 4.8mm Ball End Set & Ball Bearing Hub, genuine official replacement part from Xpress...
Model: XP-10048
Description:
This is Xpress 4.8mm Ball for Upper Link Set, genuine official replacement part from Xpress for Xpresso K1, M1...
Model: XP-10045
Description:
This is 4.8mm Ball Inner Thread 10pcs For Xpresso K1 M1, genuine official replacement part from Xpress...
Model: XP-10987
Description:Replacement part for the Execute MF1, keep important spares in your pits box so your raceday or practice day isn't cut short!..
Model: XP-10253
Description:
This is 4.8mm Low Profile Ball End, genuine official replacement part from Xpress...
Model: XP-10682
Description:This is 4.8mm Low Profile Ball End, genuine official replacement part from Xpress...
Model: XP-10251
Description:
This is 4.8mm Low Profile Ball End, genuine official replacement part from Xpress...
Model: XP-10254
Description:
A redesigned ball end set for replacing all the 4.8mm ball ends on the Execute XQ1 / XQ1S. Also compatible with other Execute Series Chassis...
Model: XP-10899
Description:Replacement parts for the Xpress Arrow AT1, genuine part for Xpress series of cars...
Model: XP-11016
Description:Aluminum gear differential outdrives for a more lightweight drivetrain increasing braking and acceleration response!..
Model: XP-10941
Aluminum light weight differential outdrive to reduce the weight of the drivetrain on your Xpress Arrow! Allowing for a more efficient drivetrain resulting in better speeds! Note: Requires 4mm thickness blades #XP-10876. Not compatible with #XP-10946 Aluminum Rear Universals...
Model: XP-10948
This is Xpress 5.5mm Ball, longer gap between the flange and the shock allowing greater movement angle...
Model: XP-10895
This is Xpress 5.5mm Ball, longer gap between the flange and the shock allowing greater movement angle...
Model: XP-10121
Description:
This is 5.5mm Pivot Ball, genuine official replacement part from Xpress...
Model: XP-40023
Description:
Replacement driver tips for Xpress's Aluminum 7075 lightweight drivers! Special treated steel tips which promotes high accuracy and long lifetime due to low wear! Stripes on the tooltip allows you to easily spot the size of the tip as well as the laser engraved size markings!..
Model: XP-10047
Xpress 5.5mm Suspersion Arm Ball 3.8mm Thread 10pcs For Xpresso K1 M1 #XP-10047
Description:
This is Xpress 5.5mm Suspersion Arm Ball Set, genuine official replacement part from Xpress...
Model: XP-10984
Description:Lift your servo, receiver and fan off your chassis to not affect your chassis flex. Graphite piece which extends from underneath the servo for you to stick your electronics on...
Model: XP-40086
Reduce the amount of free play you might get from bearing slop in your driveshafts with these shims. Applicable to the front or rear...
Model: XP-40273
Description:Titanium turnbuckles for use on the Xpress Execute XQ3S / XQ11 / XQ11R, longer length than original and a machined 1.5mm hex slot for easy installation!..
Model: XP-11068
Genuine Xpress replacement part, keep important spares in your pits box so your raceday or practice day isn't cut short!
..
Model: XP-40024
Description:
Replacement driver tips for Xpress's Aluminum 7075 lightweight drivers! Special treated steel tips which promotes high accuracy and long lifetime due to low wear! Stripes on the tooltip allows you to easily spot the size of the tip as well as the laser engraved size markings!..
Model: XP-10039
Xpress Aluminum 7075 Damper Cover Set For Xpresso K1 M1 #XP-10039
Description:
This is Xpress Aluminum 7075 Damper Cover Set, genuine official replacement part from Xpress...
Model: XP-10027
Xpress 7075 Aluminum Front Bulkhead Left For Xpresso K1 M1 #XP-10027
Description:
This is Xpress 7075 Aluminum Front Bulkhead Left, genuine official replacement part from Xpress...
Model: XP-10028
Xpress 7075 Aluminum Front Bulkhead Right For Xpresso K1 M1 #XP-10028
Description:
This is Xpress 7075 Aluminum Front Bulkhead Right, genuine official replacement part from Xpress...
Model: XP-10010
Description:This is Xpress 7075 Aluminum Gear Differential Outdrive Adaptor, genuine official replacement part from Xpress...
Model: XP-10031
Xpress Aluminum 7075 Rear Upper Clamp 1 pair For Xpresso K1 M1 #XP-10031
Description:
This is Xpress Aluminum 7075 Rear Upper Clamp pair, genuine official replacement part from Xpress...
Model: XP-10035
Xpress Aluminum 7075 Servo Mount Front Bracket For Xpresso K1 M1 #XP-10035
Description:
This is Xpress Aluminum 7075 Servo Mount Front Bracket, genuine official replacement part from Xpress...
Model: XP-10034
Xpress Aluminum 7075 Servo Mount Rear Bracket For Xpresso K1 M1 #XP-10034
Description:
This is Xpress Aluminum 7075 Servo Mount Rear Bracket , genuine official replacement part from Xpress...
Model: XP-10038
Xpress Aluminum 7075 Shock Tower Post For Xpresso K1 M1 #XP-10038
Description:
This is Xpress Aluminum 7075 Shock Tower Post, genuine official replacement part from Xpress...
Model: XP-10036
Xpress Aluminum 7075 Steering Adapter For Xpresso K1 M1 #XP-10036
Description:
This is Xpress Aluminum 7075 Steering Adapter, genuine official replacement part from Xpress...
Model: XP-40087
Description:Red turnbuckles to upgrade your existing Xpress vehicle to match the turnbuckles to the red on the rest of your car!..
Model: XP-40088
Xpress 7075 Aluminum Turnbuckle 24mm 2pcs #XP-40088
Description:
Red turnbuckles to upgrade your existing Xpress vehicle to match the turnbuckles to the red on the rest of your car!..
Model: XP-40089
Description:Red turnbuckles to upgrade your existing Xpress vehicle to match the turnbuckles to the red on the rest of your car!..
Model: XP-40090
Description:Red turnbuckles to upgrade your existing Xpress vehicle to match the turnbuckles to the red on the rest of your car!..
Model: XP-40091
Description:
Red turnbuckles to upgrade your existing Xpress vehicle to match the turnbuckles to the red on the rest of your car!..
Model: XP-40100
Xpress 7075 Aluminum Turnbuckle 48mm 2pcs #XP-40100
Description:
Red turnbuckles to upgrade your existing Xpress vehicle to match the turnbuckles to the red on the rest of your car!..
Model: XP-10981
Description:Lift your servo, receiver and fan off your chassis to not affect your chassis flex. Graphite piece which extends from underneath the servo for you to stick your electronics on. Use the 70mm plate on mid mount cars and 90mm on standard layout cars (XQ1, XQ2S)..
Model: XP-10980
Description:Lift your servo, receiver and fan off your chassis to not affect your chassis flex. Graphite piece which extends from underneath the servo for you to stick your electronics on. Choice of lifting either only the servo or electronics as well with the both plates included...